PC21.FR : Nouveaux produits Ram Mounts

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support

(référence créée le 18.09.25) RUT7631 RAM-HOL-HON12PDHLU

172,45 € HT
206,94 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDU :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAddition

(référence créée le 18.09.25) RUT7632 RAM-HOL-GE4PDU

204,79 € HT
245,74 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDHU

- :

• Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC
• CE

• RoHSAdditional information: Devices shown are not inc

(référence créée le 18.09.25) RUT7633 RAM-HOL-ZE26PDHU

154,06 € HT
184,87 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDHLU

- :Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh

(référence créée le 18.09.25) RUT7634 RAM-HOL-ZE32PDHLU

174,62 € HT
209,54 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25LU :

• Compatible with Zebra KeyboardEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp

• T

(référence créée le 18.09.25) RUT7635 RAM-HOL-ZE25LU

135,52 € HT
162,62 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU :Compatible with accessori

(référence créée le 18.09.25) RUT7636 RAM-HOL-ZE22PLU

162,14 € HT
194,56 € TTC

Sur
Commande

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PD2U :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generati

(référence créée le 18.09.25) RUT7637 RAM-GDS-DOCKL-ZE20PD2U

165,93 € HT
199,11 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PU :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepar

(référence créée le 18.09.25) RUT7638 RAM-HOL-GE4PU

190,19 € HT
228,22 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4U :

• Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp

• Temp Right or NFC repeaterAdditional information: This holder

(référence créée le 18.09.25) RUT7639 RAM-HOL-GE4U

135,00 € HT
162,00 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC rea

(référence créée le 18.09.25) RUT7640 RAM-HOL-ZE25PDHU

265,67 € HT
318,80 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Frame and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22U :Compatible with accessoriesEasy insertion and removalWith LatchAdditional mounting plate for attaching additional

(référence créée le 18.09.25) RUT7641 RAM-HOL-ZE22U

103,18 € HT
123,81 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA

(référence créée le 18.09.25) RUT7642 RAM-HOL-ZE25PHLU

215,49 € HT
258,58 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PHLU :

• Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS
• CE

• RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PHLU holder is supplied.

(référence créée le 18.09.25) RUT7643 RAM-HOL-ZE26PHLU

166,44 € HT
199,72 € TTC

Sur
Commande

This RAM Mounts Form-Fit (latch) holder is suitable for Zebra ET4x 10? series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PNLLU :

• Compatible with PowerPack batterieEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS
• WEEE

• CE & UKCAAdditional

(référence créée le 18.09.25) RUT7644 RAM-HOL-ZE21PNLLU

104,33 € HT
125,19 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal N

(référence créée le 18.09.25) RUT7645 RAM-HOL-ZE25PDHLU

289,73 € HT
347,67 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PLU :Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for atta

(référence créée le 18.09.25) RUT7646 RAM-HOL-ZE25PLU

217,25 € HT
260,70 € TTC

Sur
Commande

This RAM Mounts EZ-Roll?r (key-locking) holder is suitable for Zebra ET4x 8? series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PKLU :

• Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS
• WEEE

• CE & UK

(référence créée le 18.09.25) RUT7647 RAM-HOL-ZE20PKLU

124,33 € HT
149,19 € TTC

Sur
Commande

Ram Mounts This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDU

- :

• Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC

• CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDU holder is sup

(référence créée le 18.09.25) RUT7648 RAM-HOL-ZE32PDU

122,08 € HT
146,49 € TTC

Sur
Commande

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PDU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation pr

(référence créée le 18.09.25) RUT7649 RAM-GDS-DOCKL-ZE21PDU

162,50 € HT
195,00 € TTC

Sur
Commande

This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PHU :

• Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS
• CE

• RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PHU holder is supplied.

(référence créée le 18.09.25) RUT7650 RAM-HOL-ZE26PHU

143,17 € HT
171,80 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PLU :Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionLockable with keyCan be used with and without rugged bo

(référence créée le 18.09.25) RUT7651 RAM-HOL-HON12PLU

130,81 € HT
156,97 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 without Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PL-1U :

• Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with keyInput Connector: USB-AInput Cable Length: ca. 125 cmCertifications: RoHS
• WEEE

• CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PL-1U holder is supplied.

(référence créée le 18.09.25) RUT7652 RAM-HOL-ZE24PL-1U

97,07 € HT
116,48 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 with Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PLU :

• Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with KeysInput Connector: USB-A Input Cable Length: ca. 125 cmCertifications: RoHS
• WEEE

• CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PLU holder is supplied.

(référence créée le 18.09.25) RUT7653 RAM-HOL-ZE24PLU

92,70 € HT
111,24 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2U :Compatible with Zebr

(référence créée le 18.09.25) RUT7654 RAM-HOL-ZE25PD2U

213,90 € HT
256,68 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HO

(référence créée le 18.09.25) RUT7655 RAM-HOL-HON12PHLU

179,85 € HT
215,82 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDKLU :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable w

(référence créée le 18.09.25) RUT7656 RAM-HOL-GE4PDKLU

226,52 € HT
271,82 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDU

- :

• Spring-loaded design for easy insertion and removalCharging functionInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC
• CE

• RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PDU holder is supplied.

(référence créée le 18.09.25) RUT7657 RAM-HOL-ZE26PDU

95,32 € HT
114,38 € TTC

Sur
Commande

This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PHLU :

• Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC

• CE & RoHSAdditional information: Devices shown are not

(référence créée le 18.09.25) RUT7658 RAM-HOL-ZE32PHLU

161,84 € HT
194,20 € TTC

Sur
Commande

This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32U :Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32U holder is supplied.

(référence créée le 18.09.25) RUT7659 RAM-HOL-ZE32U

62,02 € HT
74,42 € TTC

Sur
Commande

This RAM Mounts GDS EZ-Roll?r holder is suitable for Zebra ET4x 10? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE21PDU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleev

(référence créée le 18.09.25) RUT7661 RAM-GDS-DOCK-ZE21PDU

128,92 € HT
154,70 € TTC

Sur
Commande

This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PHU :

• Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC

• CE & RoHSAdditional information: Devices shown are not included in the delivery.Only th

(référence créée le 18.09.25) RUT7662 RAM-HOL-ZE32PHU

139,53 € HT
167,43 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET40 & ET45 10? series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PKLU :

• Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged BootLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS
• WEEE

• CE & UKC

(référence créée le 18.09.25) RUT7663 RAM-HOL-ZE21PKLU

128,86 € HT
154,63 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Produc

(référence créée le 18.09.25) RUT7664 RAM-HOL-ZE22PDLU

199,57 € HT
239,48 € TTC

Sur
Commande

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PDU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation pro

(référence créée le 18.09.25) RUT7665 RAM-GDS-DOCKL-ZE20PDU

157,09 € HT
188,50 € TTC

Sur
Commande

Ram Mounts RAM MOUNT AND TAB-TITE FOR IPAD AIR W/ CASE AND BACKING

(référence créée le 22.09.25) RUT7666 RAM-101B2-TAB20U

82,17 € HT
98,60 € TTC

Sur
Commande

Intelliskin Charging Boot, GDS Technology, fits for : EM45

(référence créée le 30.09.25) RUT7667 RAM-GDS-SKIN-ZE37-C

52,00 € HT
62,40 € TTC

Sur
Commande

Ram Mounts IntelliSkin® Thin-CaseT for Samsung Tab A9+ (Rear Pogo

(référence créée le 01.10.25) RUT7668 RAM-GDS-SKIN-SAM88-TCB

164,01 € HT
196,81 € TTC

Sur
Commande

Intelliskin Charging Boot, GDS Technology, fits for : EM45

(référence créée le 02.10.25) RUT7669 RAM-GDS-SKIN-ZE37-C-NC

50,66 € HT
60,79 € TTC

Sur
Commande

Intelliskin Charging Boot, GDS Technology, fits for : EM45

(référence créée le 02.10.25) RUT7670 RAM-GDS-SKIN-ZE37-NC

44,27 € HT
53,12 € TTC

Sur
Commande

Ram Mounts RAM® Powered Dock + Single USB-A for Zebra

(référence créée le 16.10.25) RUT7672 RAM-HOL-ZE33PDU

109,56 € HT
131,47 € TTC

Sur
Commande

Ram Mounts RAM® Locking Powered Dock + Single USB-A for Zebra

(référence créée le 16.10.25) RUT7673 RAM-HOL-ZE33PDLU

139,59 € HT
167,50 € TTC

Sur
Commande

Ram Mounts RAM® Power + Dual USB Dock for Honeywell ScanPal EDA10A

(référence créée le 20.10.25) RUT7674 RAM-HOL-HON11PD2U

158,62 € HT
190,34 € TTC

Sur
Commande

Ram Mounts GDS® Uni-ConnT Powered Wall Dock with USB-C

(référence créée le 22.10.25) RUT7675 RAM-GDS-DOCK-W4-CU

97,02 € HT
116,42 € TTC

Sur
Commande

Ram Mounts GDS® 10-32VDC Input (12VDC Output) Hardwire Charger with

(référence créée le 07.11.25) RUT7676 RAM-GDS-CHARGE-V10-1U

49,61 € HT
59,53 € TTC

Sur
Commande

Ram Mounts 75x75mm VESA Plate with Ball and Steel Reinforced Post, D

(référence créée le 10.11.25) RUT7677 RAM-D-2461U-IN1

35,42 € HT
42,50 € TTC

Sur
Commande

Ram Mounts RAM® Quick-GripT XL Phone Mount with Low-Profile

(référence créée le 13.11.25) RUT7678 RAM-HOL-PD4-400-1U

49,17 € HT
59,00 € TTC

Sur
Commande

Ram Mounts UNPKD EZ-ROLL'R DOCK USB-C POWER ONLY FOR SAMSUNG TAB

(référence créée le 19.11.25) RUT7679 RAM-HOL-SAM60CP-NFCU

155,87 € HT
187,04 € TTC

Sur
Commande

Ram Mounts IntelliSkin® Thin-CaseT for Tab Active5 & 3 (Rear Pogo

(référence créée le 01.12.25) RUT7680 RAM-GDS-SKIN-SAM93-TCB

161,70 € HT
194,04 € TTC

Sur
Commande

Ram Mounts RAM® Twist-LockT Triple Suction Cup Mount with

(référence créée le 01.12.25) RUT7681 RAP-365-138U

82,61 € HT
99,13 € TTC

Sur
Commande

This RAM Mounts EZ-Roll?r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-Stand.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM60CPN-1AU :Compatible with accessoriesCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionInput Connector: USB-COutput Connector: USB-A 1

(référence créée le 01.12.25) RUT7682 RAM-HOL-SAM60CPN-1AU

86,28 € HT
103,53 € TTC

Sur
Commande

This RAM Mounts EZ-Roll?r Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-StandThe back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM60CPN-CAU :Compatible with accessoriesCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionInput Connector: USB-COutput Connector: USB-C

(référence créée le 01.12.25) RUT7683 RAM-HOL-SAM60CPN-CAU

112,84 € HT
135,40 € TTC

Sur
Commande

Ram Mounts This RAM Mounts GDS holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra Handheld secure, the powered dock also leaves the device?s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V12-ZE2434CPDU

- :Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: USB-COutput Connector: USB-A (Peripheral output - 500mAh)

(référence créée le 01.12.25) RUT7684 RAM-GDS-DOCK-V12-ZE2434CPDU

114,50 € HT
137,40 € TTC

Sur
Commande

Ram Mounts This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in Dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM88CD2U

- :Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3A maxOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM88CD2U holder is

(référence créée le 01.12.25) RUT7685 RAM-GDS-DOCK-SAM88CD2U

213,12 € HT
255,74 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PKLU :

• Compatible with the Getac tablet accessoiresNot compatible with the Getac 4-point hand strap accessoryEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp

• Temp Right or NFC repeaterInput Connector: 5.5

(référence créée le 01.12.25) RUT7686 RAM-HOL-GE5PKLU

258,42 € HT
310,10 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.The included RAM NFC extender supports the NFC function with a range of up to 30 cm.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, GDS Roto-Mag and side accessory attachments.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKL-NFCU :Compatible with accessoriesIncluding RAM NFC-ExtenderCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionLockable with keyInput Connector: USB-CInput Voltage: 5.3-5.4 VDCOutput Voltage:

(référence créée le 01.12.25) RUT7687 RAM-HOL-SAM58CPKL-NFCU

189,36 € HT
227,23 € TTC

Sur
Commande

Ram Mounts This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM88CDU

- :Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-A (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-SAM88CDU holder is supplied.

(référence créée le 01.12.25) RUT7688 RAM-GDS-DOCK-SAM88CDU

203,44 € HT
244,12 € TTC

Sur
Commande

This RAM Mounts EZ-Roll?r Form-Fit holder is suitable for Samsung Tab Active3 in an OtterBox uniVERSE case.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM60CP-OT1U :Compatible with accessoriesCan only be used with OtterBox uniVERSE caseAccess to the stylus penEasy insertion and removalCharging functionInput Connector: USB-CInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmAdditional information:This product will not support the 'No Battery Mode' function.Devices shown are not included in the delivery.Only the RAM-HOL-SAM60CP-OT1U holder is supplied.

(référence créée le 01.12.25) RUT7689 RAM-HOL-SAM60CP-OT1U

71,64 € HT
85,96 € TTC

Sur
Commande

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11U :

• Compatible with OEM hand strap Easy insertion and removalWith LatchPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamond ball base) for additional devices or peripheral accessoriesCertifications: RoHS
• WEEE

• CE & FCCAdditional inform

(référence créée le 01.12.25) RUT7690 RAM-HOL-HON11U

99,80 € HT
119,76 € TTC

Sur
Commande

Ram Mounts This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 and Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-C cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62C-CU

- :Compatible with GDS hand-stand Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: USB-C (Peripheral output - 500mAh)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cmAdditional information: This product will not support the 'No Battery Mode' function. Devices shown are not i

(référence créée le 01.12.25) RUT7691 RAM-GDS-DOCK-SAM62C-CU

182,29 € HT
218,74 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PDKLU :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with keyAd

(référence créée le 01.12.25) RUT7692 RAM-HOL-GE5PDKLU

279,27 € HT
335,12 € TTC

Sur
Commande

This RAM Mounts GDS Desktop Dock with Power Delivery is suitable for smartphones and tablets in IntelliSkin Next Gen, IntelliSkin & IntelliSkin HD protective sleeves.The charging station offers data connectivity via USB-C and the charging function.It is also ideal for permanent use (insertion/removal).Product features RAM Mounts RAM-GDS-DOCK-D2CM-NDU-GRY :

• Only compatible with IntelliSkin Next Gen protective sleeveEasy insertion and removalPower Delivery & DeX Support (Next Gen)Input Connector: USB-COutput Voltage:5V @ 2A5V @ 3A12V @ 1.5A12V @ 3AOutput Power: 48W TotalProduct dimensions:Height: 5
• 08 cmWidth: 7

• 62 cmDepth: 10
• 41 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-DOCK-D2CM-NDU-GRY Dock is supplied.

(référence créée le 01.12.25) RUT7693 RAM-GDS-DOCK-D2CM-NDU-GRY

114,93 € HT
137,91 € TTC

Sur
Commande

Ram Mounts This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab A9+ in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM88CD2U

- :Compatible with GDS hand-stand Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AOutput Connector: 2x USB-A (Peripheral output - 900mAh per Port)Input Cable Length: ca. 21 cmOutput Cable Length: ca. 21 cm· Prepared for GDS 12-VDC Axial cooling fanAdditional information: This product will not support the 'N

(référence créée le 01.12.25) RUT7694 RAM-GDS-DOCKL-SAM88CD2U

241,36 € HT
289,63 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PD2KLU :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with

(référence créée le 01.12.25) RUT7695 RAM-HOL-GE5PD2KLU

297,62 € HT
357,14 € TTC

Sur
Commande

This RAM Mounts GDS IntelliSkin Next Gen protective sleeve is designed for the Samsung Galaxy Tab A9+ and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible :

• the camera
• buttons
• and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations

• making it ideal for professional use ? whether in vehicles
• at the workplace
• or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM88-NG-GRY:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.0Transfer S

(référence créée le 01.12.25) RUT7696 RAM-GDS-SKIN-SAM88-NG-GRY

87,31 € HT
104,77 € TTC

Sur
Commande

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons allow you to continue using them without any problems.An RAM NFC-Extender module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPT-1AU :Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skinSlim-profile design at 2.28' depthAccess to the stylus penOptional attachment of additional devices or accessoriesEasy insertion and removalWith LatchCharging functionInput Connector: USB-COutput Connector: USB-A (Peripheral output -

(référence créée le 01.12.25) RUT7697 RAM-HOL-SAM58CPT-1AU

103,54 € HT
124,24 € TTC

Sur
Commande

This RAM Mounts GDS Tough-Dock (Latch) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-SAM62CP-NFCU :Easy insertion and removalCharging functionWith LatchInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmPrepared for GDS-FAN 12-VDC axial fanIncluding RAM NFC-ExtenderAdditional information: This product is not compatible with the GDS Hand-Stand.This holder will not support any NFC functionality of the Tab Active2Potential interference of NFC functionality may occur when positioned close to

(référence créée le 01.12.25) RUT7698 RAM-GDS-DOCK-SAM62CP-NFCU

219,85 € HT
263,82 € TTC

Sur
Commande

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PKLU :Compatible with OEM hand strap Easy insertion and removalCharging functionLockable with keyPrepared for RAM NFC Extender & RAM Vent-Temp2-Hole side mount (Diamo

(référence créée le 01.12.25) RUT7699 RAM-HOL-HON11PKLU

160,95 € HT
193,14 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX80 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PD2U :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional

(référence créée le 01.12.25) RUT7700 RAM-HOL-GE5PD2U

274,33 € HT
329,19 € TTC

Sur
Commande

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons allow you to continue using them without any problems.An RAM NFC-Extender module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLT-AU :Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skinSlim-profile design at 2.28' depthAccess to the stylus penOptional attachment of additional devices or accessoriesEasy insertion and removalLockable with keyCharging functionInput Connector: USB-COutput Connector: USB-A (Perip

(référence créée le 01.12.25) RUT7701 RAM-HOL-SAM58CPKLT-AU

137,71 € HT
165,25 € TTC

Sur
Commande

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable & DB9 connector.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PD2-DB9KLU :Compatible with OEM hand strap Easy insertion and removalCharging fu

(référence créée le 01.12.25) RUT7702 RAM-HOL-HON11PD2-DB9KLU

236,83 € HT
284,19 € TTC

Sur
Commande

This RAM Mounts GDS (Key-Locking) holder is suitable for Zebra TC2x & TC5x series with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra Handheld secure, the powered dock also leaves the device?s top scanner and buttons exposed and usable.Available space in the back accommodates extended battery packs and the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-V12-ZE2434CPDHU :Only compatible with the In

(référence créée le 01.12.25) RUT7703 RAM-GDS-DOCKL-V12-ZE2434CPDHU

160,35 € HT
192,42 € TTC

Sur
Commande

This RAM Mounts Form Fit (key-locking) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PDKLU :Compatible with OEM hand strap Easy insertion and removalCharging functionLockable with k

(référence créée le 01.12.25) RUT7704 RAM-HOL-HON11PDKLU

172,45 € HT
206,94 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX80 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5KLU :

• Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable with KeysAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp

• Temp Right or NFC repeaterAdditional information: This

(référence créée le 01.12.25) RUT7705 RAM-HOL-GE5KLU

183,99 € HT
220,78 € TTC

Sur
Commande

This RAM Mounts Form Fit (Latch) holder is suitable for the Honeywell ScanPal EDA10A Tablet in OEM protective boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Honeywell ScanPal EDA10A.An RAM NFC add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-HON11PDU :Compatible with OEM hand strap Easy insertion and removalCharging functionWith LatchPrepared for

(référence créée le 01.12.25) RUT7706 RAM-HOL-HON11PDU

145,88 € HT
175,05 € TTC

Sur
Commande

This RAM Mounts Form-Fit Low Profile (Latch) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C/A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons allow you to continue using them without any problems.An RAM NFC-Extender module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPT-CAU :Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skinSlim-profile design at 2.28' depthAccess to the stylus penOptional attachment of additional devices or accessoriesEasy insertion and removalWith LatchCharging functionInput Connector: USB-COutput Connector: USB-C & USB-A (Periphera

(référence créée le 01.12.25) RUT7707 RAM-HOL-SAM58CPT-CAU

128,16 € HT
153,79 € TTC

Sur
Commande

This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra TC53 & TC58 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all device functions remain fully accessible the scanner, camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs as well as the OEM hand strap.The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE34-GRY :

• Compatible with standard and extended battery packs and OEM hand strapContinued access to scanner

• camera and buttonsCharging and data sync functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE34-GRY is su

(référence créée le 01.12.25) RUT7708 RAM-GDS-SKIN-ZE34-GRY

38,74 € HT
46,48 € TTC

Sur
Commande

This RAM Mounts Form-Fit Low Profile (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons allow you to continue using them without any problems.An RAM NFC-Extender module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLTU :Compatible with accessories such as RAM NFC-Repeater Can only be used with OEM or RAM skinSlim-profile design at 2.28' depthAccess to the stylus penOptional attachment of additional devices or accessoriesEasy insertion and removalLockable with keyCharging functionInput Connector: USB-CInput Voltage: 5.3-5.4 VDCOutput Voltage: 5 VDCInput Cable Length: ca. 21 cmAdditional informatio

(référence créée le 01.12.25) RUT7709 RAM-HOL-SAM58CPKLTU

127,38 € HT
152,85 € TTC

Sur
Commande

This RAM Mounts GDS holder is suitable for Zebra EC50 & EC 55 with the IntelliSkin protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged.While keeping the Zebra EC5x secure, the powered dock also leaves the device?s top scanner and buttons exposed and usable.Available space in the back accommodates standard and extended battery packs as well with the Zebra hand strap.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-V12-ZE16CPDU :Only compatible with the IntelliSkin protective sleeveSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionInput Connector: USB-COutput Connector: USB-A (Peripheral output

(référence créée le 01.12.25) RUT7710 RAM-GDS-DOCK-V12-ZE16CPDU

139,92 € HT
167,90 € TTC

Sur
Commande

This RAM Mounts GDS Tough-Dock (Key-Locking) holder is suitable for the Samsung Tab Active2, Active3 und Active5 in IntelliSkin Next Gen protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-SAM62CP-NFCU :Easy insertion and removalCharging functionLockable with keyInput Connector: USB-CPower Output: 15WOutput Voltage: 5-12V @ 3AInput Cable Length: ca. 21 cmPrepared for GDS-FAN 12-VDC axial fanIncluding RAM NFC-ExtenderAdditional information: This product is not compatible with the GDS Hand-Stand.This holder will not support any NFC functionality of the Tab Active2Potential interference of NFC functionality may occur when posit

(référence créée le 01.12.25) RUT7711 RAM-GDS-DOCKL-SAM62CP-NFCU

242,08 € HT
290,49 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX80 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the Getac 2-point hand strap can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX80.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE5PDU :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounti

(référence créée le 01.12.25) RUT7712 RAM-HOL-GE5PDU

256,44 € HT
307,72 € TTC

Sur
Commande

This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Samsung Galaxy XCover7 Pro & XCover6 Pro and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all functions remain fully accessible :

• the camera
• buttons
• and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations

• making it ideal for professional use ? whether in vehicles
• at the workplace
• or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM84-GRY:Compatible with GDS DocksInlcuded Belt ClipContinued access to camera and buttonsCharging functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-SAM84-GRY is supplied.

(référence créée le 01.12.25) RUT7713 RAM-GDS-SKIN-SAM84-GRY

48,23 € HT
57,87 € TTC

Sur
Commande

This RAM Mounts Modular Form-Fit holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-StandThe back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLN-CU :Compatible with accessoriesCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging functionLockable with keyInput Connector: USB-COutput Connector:

(référence créée le 01.12.25) RUT7714 RAM-HOL-SAM58CPKLN-CU

140,09 € HT
168,10 € TTC

Sur
Commande

This RAM Mounts Modular Form-Fit (Key-Locking) holder is suitable for Samsung Tab Active3 & Active5 in OEM or RAM protective sleeve.The holder is powered by a USB-C connection and charges the device in the dock while peripheral support is provided by the built-in USB-C and USB-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle is compatible with most RAM dock accessories including Temperature Control Accessories, RAM NFC-Extender, GDS Roto-Mag, and side accessory attachments.Modular docks are not compatible with the GDS Hand-Stand.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-SAM58CPKLN-CAU :Compatible with accessories and side accessory attachmentsCan only be used with OEM or RAM skinAccess to the stylus penEasy insertion and removalCharging function

(référence créée le 01.12.25) RUT7715 RAM-HOL-SAM58CPKLN-CAU

151,91 € HT
182,29 € TTC

Sur
Commande

Ram Mounts Form-Fit Holder for Getac ZX80

(référence créée le 03.12.25) RUT7716 RAM-HOL-GE5U

180,95 € HT
217,14 € TTC

Sur
Commande

Ram Mounts The GDS® Modular Hardwire Charger with USB Type-C Female Connector is the ideal solution for providing power to any USB Type-C GDS® vehicle solution. By connecting directly to the power source of your vehicle, the GDS® Modular Hardwire Charger delivers USB Type-C power to your device with an input voltage of 10-28V.Avoid rewiring when changing or upgrading devices by simply unplugging the power connector and installing the new charger. Always Protected. Always Connected.®FeaturesHardwire charger includes USB Type-C female connection with an input voltage of 10-28VWhen upgrading devices, avoid rewiring by unplugging power connector and attaching new charger componentsPart of the GDS® Ecosystem? to keep devices protected, connected, and charged in nearly any applicationInput voltage

10-28 V DCOutput voltage - 5V @ 1A (5W), 9V @ 2A (18W), 12V @ 2A (24W)Output current - 3A max.Input connector - female USB Type-CInput cable length - 1,2 m (including 2 Pole Flat Marine Connector)Output cable length - 150 mmOper

(référence créée le 03.12.25) RUT7717 RAM-GDS-CHARGE-V3FC-2U-NC

105,12 € HT
126,14 € TTC

Sur
Commande

This RAM Mounts GDS IntelliSkin protective sleeve is designed for the Zebra TC22 & TC27 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.Thanks to its thoughtful design, all device functions remain fully accessible the scanner, camera and buttons can still be used without restriction.Additional cutouts and clearances on the back of the IntelliSkin ensure compatibility with standard and extended battery packs as well as the OEM hand strap.The IntelliSkin case is compatible with a wide range of GDS docks.Product features RAM Mounts RAM-GDS-SKIN-ZE24-GRY :

• Compatible with standard and extended battery packs and OEM hand strapContinued access to scanner

• camera and buttonsCharging and data sync functionEasy insertion and removalAdditional information: Devices shown are not included in the delivery.Only the RAM-GDS-SKIN-ZE24-GRY is sup

(référence créée le 03.12.25) RUT7719 RAM-GDS-SKIN-ZE24-GRY

39,77 € HT
47,72 € TTC

Sur
Commande

This RAM Mounts GDS IntelliSkin Hard Case protective sleeve is designed for the Samsung Galaxy Tab Active3 & Active5 and offers reliable protection combined with convenient charging functionality.The integrated GDS connector is located within the inner frame of the case, allowing the device to be charged or continuously powered even while in use.This IntelliSkin also features an external USB-C port, so that your device can be plugged in, even when a GDS Dock is not available.Thanks to its thoughtful design, all tablet functions remain fully accessible :

• the camera
• buttons
• and ports can still be used without restriction.The IntelliSkin case is compatible with a wide range of GDS mounting systems and docking stations

• making it ideal for professional use ? whether in vehicles
• at the workplace
• or on the move.Product features RAM Mounts RAM-GDS-SKIN-SAM89-HC:Compatible with GDS DocksHolder for Stylus PenContinued access to camera and buttonsCharging functionEasy insertion and removalInput Connector: USB-C 2.

(référence créée le 03.12.25) RUT7721 RAM-GDS-SKIN-SAM89-HC

62,25 € HT
74,70 € TTC

Sur
Commande

Ram Mounts 10 QTY BULK PACK SCREEN PROTECTOR HD CLEAR TEMPERED

(référence créée le 04.12.25) RUT7722 RAP-SKIN-SP-4-10

71,83 € HT
86,19 € TTC

Sur
Commande

Ram Mounts SCREEN PROTECTOR HD CLEAR TEMPERED GLASS FOR SAMSUNG

(référence créée le 04.12.25) RUT7723 RAP-SKIN-SP-4

15,07 € HT
18,08 € TTC

Sur
Commande

Ram Mounts Screen Protector for Samsung Tab A9+

(référence créée le 05.12.25) RUT7724 RAP-SKIN-SP-5

16,61 € HT
19,93 € TTC

Sur
Commande

Ram Mounts GDS® Modular 10-30V Hardwire Charger with Type-C 2.0 Cable

(référence créée le 05.12.25) RUT7725 RAM-GDS-CHARGE-USBC-V7B1-1U

58,34 € HT
70,01 € TTC

Sur
Commande

Ram Mounts GDS® Uni-ConnT Left Locking Dock with Release Lever

(référence créée le 05.12.25) RUT7726 RAM-GDS-DOCKLL-U1CPU

137,17 € HT
164,60 € TTC

Sur
Commande

Ram Mounts GDS® 10-32VDC Input (14VDC Output) Hardwire Charger with

(référence créée le 15.12.25) RUT7727 RAM-GDS-CHARGE-V19U

50,38 € HT
60,45 € TTC

Sur
Commande

Ram Mounts GDS® 20-60VDC Input (14VDC Output) Hardwire Charger with

(référence créée le 15.12.25) RUT7728 RAM-GDS-CHARGE-V20U

42,57 € HT
51,08 € TTC

Sur
Commande

Ram Mounts Form-Fit Powered Dock for Getac ZX80

(référence créée le 15.12.25) RUT7729 RAM-HOL-GE5PU

221,10 € HT
265,32 € TTC

Sur
Commande

Ram Mounts Heavy Duty C-Clamp Base For Ball Bases & Pedestal Mounts

(référence créée le 22.12.25) RUT7730 RAM-CC1U

58,19 € HT
69,82 € TTC

Sur
Commande

Ram Mounts RAM Mounts scanner holder with magnetic Tough-Mag adapter

(référence créée le 01.01.26) RUT7731 RAP-396-MAG88U

68,13 € HT
81,75 € TTC

Sur
Commande

Ram Mounts Le RAM® 7' Pedestal Mount avec motif VESA 75 mm (RAP-D11-7-V75) est un piédestal autoportant de 7 pouces qui vous permet de monter n'importe quelle station d'accueil ou support passif RAM® pour créer une station de travail qui maintient la mobilité de votre tablette. Conçue pour la flexibilité et la stabilité, cette solution comprend une base pivotante à 180 degrés et une inclinaison de l'appareil à 180 degrés, pour le positionnement et le partage d'écran avec des collègues ou des clients.Idéal pour le commerce de détail, l'hôtellerie, la restauration et d'autres environnements de point de vente ou d'interaction client, ce support prend en charge le motif VESA 75 mm pour une large compatibilité des appareils aux côtés des stations d'accueil et des supports RAM®. Une base à visser assure une installation fixe et sécurisée, ce qui le rend parfait pour les configurations à fort trafic ou semi-permanentes.FonctionnalitésPiédestal de 7 pouces avec motif VESA 75 mmLe motif de trous VESA prend en charge la connexi

(référence créée le 16.01.26) RUT7733 RAP-D11-7-V75

44,51 € HT
53,41 € TTC

Sur
Commande

Ram Mounts La station d'accueil RAM Mounts GDS Uni-Conn est une station d'accueil autoportante conçue pour les appareils contenus dans une IntelliSkin Next-Gen, une IntelliSkin Hard Case ou une IntelliSkin Thin Case avec un adaptateur GDS Uni-Conn monté.Cette solution peut pivoter à 180 degrés et permettre à l'appareil de s'incliner à 180 degrés, ce qui la rend idéale pour les industries axées sur le client telles que la vente au détail, l'hôtellerie, la restauration et plus encore.Le support à enclenchement maintient votre appareil en place en toute sécurité tout en permettant une charge rapide grâce aux broches de contact intégrées, l'alimentation étant fournie par une connexion Power over Ethernet (PoE) via un port RJ45, tandis que les deux ports USB-A à l'arrière prennent en charge jusqu'à deux périphériques d'entrée tels que clavier, souris, scanner, etc.La station d'accueil est dotée d'une base lestée et de patins en caoutchouc qui l'empêchent de glisser sur les surfaces.Elle prend également en charge un process

(référence créée le 16.01.26) RUT7734 RAM-GDS-DOCK-D14-U1E-2A-GRY

623,41 € HT
748,09 € TTC

Sur
Commande

Cette coque de protection RAM Mounts GDS IntelliSkin Thin-Case avec Pogo-Pads est conçue pour le Samsung Galaxy Tab A9+ et est un boîtier mince, en deux parties, spécialement développé pour être utilisé avec la station d'accueil GDS Uni-Conn. Le connecteur GDS intègre une fiche USB-C qui passe à travers la coque vers les pogo-pads arrière situés dans l'adaptateur GDS Uni-Conn.Les contacts pogo plats et robustes sont conçus pour un branchement fréquent, protègent le port de l'appareil et collectent moins de saleté, ce qui les rend plus faciles à nettoyer. Un port USB-C intégré en bas de la coque permet de charger l'appareil même lorsqu'aucune station d'accueil GDS Uni-Conn n'est disponible.Grâce à sa conception réfléchie, toutes les fonctions de la tablette restent entièrement accessibles :

• la caméra

• les boutons et les ports peuvent toujours être utilisés sans restriction. L'IntelliSkin Thin-Case pour le Samsung Tab A9+ est uniquement compatible avec les stations d'accueil GDS Powered Uni-Conn.Caractéristiq

(référence créée le 16.01.26) RUT7735 RAM-GDS-SKIN-SAM88-TCB-GRY

132,94 € HT
159,52 € TTC

Sur
Commande


Société (facultatif) :
Nom :
Prénom :
Fonction (Facultatif) :
Téléphone :
E-mail :
Message :


	Demande enregistrée

	Nous vous confirmons le bon enregistrement de votre demande. Un mail de confirmation vous a été envoyé.

	Fermer

Quantité ajoutée :

Votre e-mail :