PC21.FR : Nouveaux produits Ram Mounts

Ram Mounts GDS® Uni-ConnT Powered Wall Dock with USB-C

(référence créée le 22.10.25) RUT7675 RAM-GDS-DOCK-W4-CU

82,17 € HT
98,60 € TTC

Sur
Commande

Ram Mounts RAM® Power + Dual USB Dock for Honeywell ScanPal EDA10A

(référence créée le 20.10.25) RUT7674 RAM-HOL-HON11PD2U

159,83 € HT
191,79 € TTC

Sur
Commande

Ram Mounts RAM® Locking Powered Dock + Single USB-A for Zebra

(référence créée le 16.10.25) RUT7673 RAM-HOL-ZE33PDLU

143,66 € HT
172,39 € TTC

Sur
Commande

Ram Mounts RAM® Powered Dock + Single USB-A for Zebra

(référence créée le 16.10.25) RUT7672 RAM-HOL-ZE33PDU

112,75 € HT
135,30 € TTC

Sur
Commande

Ram Mounts GDS® Modular 10-30V Power Delivery Hardwire Charger

(référence créée le 09.10.25) RUT7671 RAM-GDS-CHARGE-V3C-3U

119,61 € HT
143,53 € TTC

Sur
Commande

Intelliskin Charging Boot, GDS Technology, fits for : EM45

(référence créée le 02.10.25) RUT7670 RAM-GDS-SKIN-ZE37-NC

53,33 € HT
63,99 € TTC

Sur
Commande

Intelliskin Charging Boot, GDS Technology, fits for : EM45

(référence créée le 02.10.25) RUT7669 RAM-GDS-SKIN-ZE37-C-NC

63,74 € HT
76,48 € TTC

Sur
Commande

Ram Mounts IntelliSkin® Thin-CaseT for Samsung Tab A9+ (Rear Pogo

(référence créée le 01.10.25) RUT7668 RAM-GDS-SKIN-SAM88-TCB

119,24 € HT
143,08 € TTC

Sur
Commande

Intelliskin Charging Boot, GDS Technology, fits for : EM45

(référence créée le 30.09.25) RUT7667 RAM-GDS-SKIN-ZE37-C

65,03 € HT
78,03 € TTC

Sur
Commande

Ram Mounts RAM MOUNT AND TAB-TITE FOR IPAD AIR W/ CASE AND BACKING

(référence créée le 22.09.25) RUT7666 RAM-101B2-TAB20U

80,52 € HT
96,62 € TTC

Sur
Commande

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PDU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation pro

(référence créée le 18.09.25) RUT7665 RAM-GDS-DOCKL-ZE20PDU

143,27 € HT
171,92 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET8x 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Produc

(référence créée le 18.09.25) RUT7664 RAM-HOL-ZE22PDLU

193,43 € HT
232,11 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET40 & ET45 10? series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PKLU :

• Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged BootLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS
• WEEE

• CE & UKC

(référence créée le 18.09.25) RUT7663 RAM-HOL-ZE21PKLU

123,78 € HT
148,53 € TTC

Sur
Commande

This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PHU :

• Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC

• CE & RoHSAdditional information: Devices shown are not included in the delivery.Only th

(référence créée le 18.09.25) RUT7662 RAM-HOL-ZE32PHU

133,39 € HT
160,06 € TTC

Sur
Commande

This RAM Mounts GDS EZ-Roll?r holder is suitable for Zebra ET4x 10? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE21PDU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleev

(référence créée le 18.09.25) RUT7661 RAM-GDS-DOCK-ZE21PDU

120,79 € HT
144,94 € TTC

Sur
Commande

This RAM Mounts GDS EZ-Roll?r holder is suitable for Zebra ET4x 8? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCK-ZE20PU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation protective sleeveInput Connector: USB-CPower Output: 60WOutput Voltage: 5-20V @ 3AInput

(référence créée le 18.09.25) RUT7660 RAM-GDS-DOCK-ZE20PU

87,97 € HT
105,56 € TTC

En stock
1 pièce

This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32U :Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32U holder is supplied.

(référence créée le 18.09.25) RUT7659 RAM-HOL-ZE32U

64,69 € HT
77,62 € TTC

Sur
Commande

This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PHLU :

• Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC

• CE & RoHSAdditional information: Devices shown are not

(référence créée le 18.09.25) RUT7658 RAM-HOL-ZE32PHLU

153,46 € HT
184,15 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDU

- :

• Spring-loaded design for easy insertion and removalCharging functionInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC
• CE

• RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PDU holder is supplied.

(référence créée le 18.09.25) RUT7657 RAM-HOL-ZE26PDU

92,93 € HT
111,51 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Key-Locking) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDKLU :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalLockable w

(référence créée le 18.09.25) RUT7656 RAM-HOL-GE4PDKLU

209,13 € HT
250,95 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HO

(référence créée le 18.09.25) RUT7655 RAM-HOL-HON12PHLU

166,62 € HT
199,94 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PD2U :Compatible with Zebr

(référence créée le 18.09.25) RUT7654 RAM-HOL-ZE25PD2U

206,28 € HT
247,53 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 with Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PLU :

• Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with KeysInput Connector: USB-A Input Cable Length: ca. 125 cmCertifications: RoHS
• WEEE

• CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PLU holder is supplied.

(référence créée le 18.09.25) RUT7653 RAM-HOL-ZE24PLU

86,19 € HT
103,42 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC22 & TC27 without Rugged Boot.The holder is powered by a USB-A connector and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE24PL-1U :

• Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated stylus holder on the side of the dockOnly usable with Rugged BootLockable with keyInput Connector: USB-AInput Cable Length: ca. 125 cmCertifications: RoHS
• WEEE

• CE & UKCAAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE24PL-1U holder is supplied.

(référence créée le 18.09.25) RUT7652 RAM-HOL-ZE24PL-1U

90,47 € HT
108,56 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PLU :Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functionLockable with keyCan be used with and without rugged bo

(référence créée le 18.09.25) RUT7651 RAM-HOL-HON12PLU

120,73 € HT
144,87 € TTC

Sur
Commande

This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PHU :

• Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS
• CE

• RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PHU holder is supplied.

(référence créée le 18.09.25) RUT7650 RAM-HOL-ZE26PHU

133,96 € HT
160,75 € TTC

Sur
Commande

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 10? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE21PDU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generation pr

(référence créée le 18.09.25) RUT7649 RAM-GDS-DOCKL-ZE21PDU

148,19 € HT
177,82 € TTC

Sur
Commande

Ram Mounts This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDU

- :

• Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC

• CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PDU holder is sup

(référence créée le 18.09.25) RUT7648 RAM-HOL-ZE32PDU

119,01 € HT
142,81 € TTC

Sur
Commande

This RAM Mounts EZ-Roll?r (key-locking) holder is suitable for Zebra ET4x 8? series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PKLU :

• Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS
• WEEE

• CE & UK

(référence créée le 18.09.25) RUT7647 RAM-HOL-ZE20PKLU

116,58 € HT
139,89 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PLU :Compatible with Zebra KeyboardEasy insertion and removalAdditional mounting plate for atta

(référence créée le 18.09.25) RUT7646 RAM-HOL-ZE25PLU

179,52 € HT
215,42 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal N

(référence créée le 18.09.25) RUT7645 RAM-HOL-ZE25PDHLU

274,64 € HT
329,56 € TTC

Sur
Commande

This RAM Mounts Form-Fit (latch) holder is suitable for Zebra ET4x 10? series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE21PNLLU :

• Compatible with PowerPack batterieEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCInput Cable Length: ca. 100 cmCertifications: RoHS
• WEEE

• CE & UKCAAdditional

(référence créée le 18.09.25) RUT7644 RAM-HOL-ZE21PNLLU

103,92 € HT
124,70 € TTC

En stock
2 pièces

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PHLU :

• Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS
• CE

• RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PHLU holder is supplied.

(référence créée le 18.09.25) RUT7643 RAM-HOL-ZE26PHLU

155,68 € HT
186,81 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA

(référence créée le 18.09.25) RUT7642 RAM-HOL-ZE25PHLU

209,67 € HT
251,60 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Frame and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22U :Compatible with accessoriesEasy insertion and removalWith LatchAdditional mounting plate for attaching additional

(référence créée le 18.09.25) RUT7641 RAM-HOL-ZE22U

106,77 € HT
128,12 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC rea

(référence créée le 18.09.25) RUT7640 RAM-HOL-ZE25PDHU

252,41 € HT
302,89 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4U :

• Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepared for RAM Vent-Temp

• Temp Right or NFC repeaterAdditional information: This holder

(référence créée le 18.09.25) RUT7639 RAM-HOL-GE4U

123,68 € HT
148,41 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PU :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAdditional mounting plate for attaching additional devices or accessoriesPrepar

(référence créée le 18.09.25) RUT7638 RAM-HOL-GE4PU

175,18 € HT
210,21 € TTC

En stock
1 pièce

This RAM Mounts GDS Form-Fit (Key-Locking) holder is suitable for Zebra ET4x 8? series with IntelliSkin Next Generation protective sleeve.The holder is powered by a USB-C port and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-GDS-DOCKL-ZE20PD2U :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesCan only be used with IntelliSkin Next Generati

(référence créée le 18.09.25) RUT7637 RAM-GDS-DOCKL-ZE20PD2U

157,31 € HT
188,77 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22PLU :Compatible with accessori

(référence créée le 18.09.25) RUT7636 RAM-HOL-ZE22PLU

161,94 € HT
194,32 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablet with or without Zebra Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25LU :

• Compatible with Zebra KeyboardEasy insertion and removalLockable with keyAdditional mounting plate for attaching additional devices or accessoriesUsable with RAM Vent-Temp

• T

(référence créée le 18.09.25) RUT7635 RAM-HOL-ZE25LU

138,48 € HT
166,17 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDHLU

- :Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh

(référence créée le 18.09.25) RUT7634 RAM-HOL-ZE32PDHLU

165,13 € HT
198,15 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PDHU

- :

• Spring-loaded design for easy insertion and removalCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 5.4VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertification: FCC
• CE

• RoHSAdditional information: Devices shown are not inc

(référence créée le 18.09.25) RUT7633 RAM-HOL-ZE26PDHU

144,81 € HT
173,77 € TTC

Sur
Commande

This RAM Mounts Form-Fit (Latch) holder is suitable for the Getac ZX10 rugged tablet.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.Tablet accessories such as the optional battery or the multifunctional Getac hard handle can also be used.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the Getac ZX10.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-GE4PDU :Compatible with the Getac tablet accessoiresNot compatible with the Getac hand strap accessoryEasy insertion and removalWith LatchAddition

(référence créée le 18.09.25) RUT7632 RAM-HOL-GE4PDU

188,78 € HT
226,53 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (key-locking) holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support

(référence créée le 18.09.25) RUT7631 RAM-HOL-HON12PDHLU

159,63 € HT
191,55 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC73 & TC78.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17L-NP-1U :Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderLockable with keyAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17L-NP-1U holder is supplied.

(référence créée le 18.09.25) RUT7629 RAM-HOL-ZE17L-NP-1U

62,91 € HT
75,49 € TTC

Sur
Commande

This RAM Mounts EZ-Roll?r holder is suitable for Zebra ET4x 8? series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PDU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Input Connector: 5.5mm DCOutput Connector: USB-A 2.0

(référence créée le 18.09.25) RUT7628 RAM-HOL-ZE20PDU

86,19 € HT
103,42 € TTC

Sur
Commande

This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PLU :

• Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyInput Connector: 5.5mm DCInput Voltage: 9VInput Cable Length: ca. 100 cmCertifications: FCC

• CE & RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE32PLU holder is supplied.

(référence créée le 18.09.25) RUT7627 RAM-HOL-ZE32PLU

120,98 € HT
145,17 € TTC

Sur
Commande

This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PHU :Spr

(référence créée le 18.09.25) RUT7626 RAM-HOL-HON12PHU

125,42 € HT
150,50 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC73 & TC78.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle and is also charged via a 5.5mm connector.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE17L-1U :Compatible with the Zebra HandstrapSpring-loaded design for easy insertion and removalIntegrated Stylus holderCharging functionLockable with keyInput Connector: 5.5mm DCInput Cable Length: ca. 125 cmAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE17L-1U holder is supplied.

(référence créée le 18.09.25) RUT7625 RAM-HOL-ZE17L-1U

82,07 € HT
98,48 € TTC

Sur
Commande

Ram Mounts This RAM Mounts spring loaded (key-locking) holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDLU

- :

• Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionLockable with keyInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput Cable Length: ca. 100 cmOutput Cable Length: ca. 25 cmCertifications: FCC

• CE & RoHSAdditional information: Devices shown are not included in the delivery.Only t

(référence créée le 18.09.25) RUT7624 RAM-HOL-ZE32PDLU

142,72 € HT
171,26 € TTC

Sur
Commande

Ram Mounts This RAM Mounts spring loaded holder is suitable for Zebra MC9300 & MC9400 with or without rugged boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device. The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-ZE32PDHU

- :Spring-loaded design for easy insertion and removalIncluding shims for use without rugged bootClip holder for stylusAllows scanning while dockedCharging functionHeated Pogo-PinsInput Connector: 5.5mm DCOutput Connector: USB-A 2.0 (Peripheral output - 500 mAh @ 5V)Input Voltage: 9VInput

(référence créée le 18.09.25) RUT7623 RAM-HOL-ZE32PDHU

144,73 € HT
173,67 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET4x 8? series with Rugged Boot.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cradle also allows the tablet's scanning function to continue to be used because of the cutout at the back.Tablet accessories such as PowerPack batteries can also be stored inside.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE20PDKLU :Compatible with PowerPack batterieEasy insertion and removalAdditional mounting plate for attaching additional devices or accessoriesOnly for Zebra Tablets within Rugged Frame (Boot)Lockable with keyInput Connector: 5.5

(référence créée le 18.09.25) RUT7622 RAM-HOL-ZE20PDKLU

126,38 € HT
151,65 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in dual USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader

(référence créée le 18.09.25) RUT7621 RAM-HOL-ZE25PD2HU

256,60 € HT
307,92 € TTC

En stock
1 pièce

This RAM Mounts Form-Fit holder is suitable for the Getac ZX70 rugged tablet.The cut-outs on the buttons and ports allow you to continue using them without any problems.The RAM NFC Extender can be used to expand the device's internal NFC reader. The back of the device holder is prepared to support a round ball base (not included).Product features RAM Mounts RAM-HOL-GE3NU :Easy insertion and removalStylus-Pen holderAdditional mounting plate for attaching additional devices or accessoriesPrepared for the RAM NFC ExtenderAdditional information: This holder version will not support the Getac Rotating Hand Strap & Kickstand accessory.Devices shown are not included in the delivery.Only the RAM-HOL-GE3NU holder is supplied.

(référence créée le 18.09.25) RUT7620 RAM-HOL-GE3NU

84,58 € HT
101,49 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond bal

(référence créée le 18.09.25) RUT7619 RAM-HOL-HON12PDHU

136,20 € HT
163,44 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra TC8300.The holder is powered by a 5.5mm DC connection and charges the device in the dock.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-ZE26PLU :

• Spring-loaded design for easy insertion and removalCharging functionLockable with keyInput Connector: 5.5mm DCInput Voltage: 5.4VInput Cable Length: ca. 100 cmCertification: FSS
• CE

• RoHSAdditional information: Devices shown are not included in the delivery.Only the RAM-HOL-ZE26PLU holder is supplied.

(référence créée le 18.09.25) RUT7618 RAM-HOL-ZE26PLU

104,34 € HT
125,20 € TTC

Sur
Commande

Ram Mounts This RAM Mounts Form-Fit (Latch) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock.This dock has built-in heating elements that provide the necessary heat required to prevent pogo pins from locking up, allowing them to operate in wet and freezing environments.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75

(référence créée le 18.09.25) RUT7617 RAM-HOL-ZE25PHU

187,41 € HT
224,89 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET80 & ET85 2-in-1 Tablet with or without Rugged Boot and Keyboard.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The cut-out on the inside of the cradle allows tablet accessories such as Zebra Expansion Back, GDS Roto-Mag and GDS Hand-Stand to be used here as well.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET8x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE22LU :Compatible with accessoriesEasy insertion and removalLockable with keyAdditional mounting plate for attachin

(référence créée le 18.09.25) RUT7616 RAM-HOL-ZE22LU

128,45 € HT
154,14 € TTC

Sur
Commande

This RAM Mounts Form-Fit holder is suitable for Honeywell CT40, CT45 & CT47.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, pull the upper part of the cradle upwards, insert the appropriate device.The spring-loaded design holds the device tightly and securely in the cradle.This dock includes an integrated stylus holder that snaps your stylus into place while not in use and is designed to accommodate OEM accessories, such as the hand strap.The cradle allows the handheld's scanning function to continue to be used because of the cutout at the back.This holder comes with optional inserts to support devices with or without the protective rubber boot.The back of the device holder is prepared to support a diamond ball base (not included).Product features RAM Mounts RAM-HOL-HON12PDU :Spring-loaded design for easy insertion and removelStylus-Pen holderIncluding optional insertsCharging functio

(référence créée le 18.09.25) RUT7615 RAM-HOL-HON12PDU

105,46 € HT
126,55 € TTC

Sur
Commande

This RAM Mounts Form-Fit (key-locking) holder is suitable for Zebra ET60 & ET65 Tablets with or without Zebra Keyboard.The holder is powered by a 5.5mm DC connection and charges the device in the dock while peripheral support is provided by the built-in USB Type-A cable.To insert the device, place the bottom of the device in the cradle and press it into the cradle until it clicks into position.The cut-outs on the buttons and ports allow you to continue using them without any problems.The 2-in-1 latch secures the tablet and also allows the keyboard to be opened and closed independently.The RAM Temp-Right can be added for thermal regulation in extremely cold environments, while the RAM Vent-Temp utilizes the vehicle's vents to direct hot or cold air to the ET6x.An NFC repeater add-on module can be used to extend the device's internal NFC reader.The back of the device holder is prepared to support a VESA 75x75 mm or round ball base (not included).Product features RAM Mounts RAM-HOL-ZE25PDLU :Compatible with Zeb

(référence créée le 18.09.25) RUT7614 RAM-HOL-ZE25PDLU

221,08 € HT
265,29 € TTC

Sur
Commande

Ram Mounts UNPKD GDS VEHICLE DOCK USBC AND PERIPHERAL DATA FOR

(référence créée le 16.09.25) RUT7613 RAM-GDS-DOCK-SAM54NCD2U

190,85 € HT
229,02 € TTC

Sur
Commande

Ram Mounts GDS 30W USB-C PD 3.0 & 18W USB-A QC 3.0

(référence créée le 16.09.25) RUT7612 RAM-GDS-CHARGE-PPS-CIGC

67,87 € HT
81,44 € TTC

Sur
Commande

Ram Mounts GDS® Desktop Dock with Power Delivery

Large Tablets

(référence créée le 10.09.25) RUT7611 RAM-GDS-DOCK-D9U

68,53 € HT
82,23 € TTC

Sur
Commande

Intelliskin Charging Boot, GDS Technology, fits for : EM45

(référence créée le 03.09.25) RUT7610 RAM-GDS-SKIN-ZE37

54,68 € HT
65,61 € TTC

Sur
Commande

Ram Mounts UNPKD RAM LOCKING DOUBLE BALL MOUNT W/ BACKING PLATE AND

(référence créée le 03.09.25) RUT7609 RAM-101L-225B2U

58,08 € HT
69,69 € TTC

Sur
Commande

Ram Mounts UNPKD EZ-ROLL'R DOCK POWER AND DATA FOR SAMSUNG TAB

(référence créée le 01.09.25) RUT7608 RAM-HOL-SAM52CP-1AU

94,16 € HT
112,99 € TTC

Sur
Commande

Ram Mounts GDS LOCKING VEHICLE DOCK USBC POWER FOR SAMSUNG TAB A9+ 11"

(référence créée le 13.08.25) RUT7607 RAM-GDS-DOCKL-SAM88CPU

196,46 € HT
235,75 € TTC

Sur
Commande

Ram Mounts RAM POWER + DUAL USB-A AND SINGLE DB9 DATA CRADLE FOR

(référence créée le 17.07.25) RUT7606 RAM-HOL-HON11PD2-DB9U

250,58 € HT
300,69 € TTC

Sur
Commande

Ram Mounts RAM GDS PD HARDWIRE CHARGER WITH TYPE C FEMALE CONNECTOR

(référence créée le 16.07.25) RUT7605 RAM-GDS-CHARGE-V3FC-2U

189,75 € HT
227,70 € TTC

En stock
1 pièce

Ram Mounts GDS VEHICLE LOCKING DOCK USBC W/ FAN FOR INTELLISKIN NG FOR

(référence créée le 03.07.25) RUT7604 RAM-GDS-DOCKLF-AP37CPU

239,03 € HT
286,83 € TTC

Sur
Commande

Ram Mounts RAM GDS POWER ONLY 6 GANG DOCK FOR TABLETS IN

(référence créée le 01.07.25) RUT7603 RAM-GDS-DOCK-6G16P

569,00 € HT
682,80 € TTC

En stock
3 pièces

Ram Mounts GDS VEHICLE DOCK USBC POWER FOR SAMSUNG TAB A9+ 11"

(référence créée le 01.07.25) RUT7602 RAM-GDS-DOCK-SAM88CPU

174,02 € HT
208,82 € TTC

Sur
Commande

Ram Mounts GDS VEHICLE USBC DOCK POWER, HEATED POGO

(référence créée le 23.05.25) RUT7601 RAM-GDS-DOCK-V12-U1CPDHU

223,74 € HT
268,48 € TTC

Sur
Commande

Ram Mounts RAM POWER + DUAL USB-A DATA KEY LOCKING CRADLE FOR

(référence créée le 13.05.25) RUT7600 RAM-HOL-HON11PD2KLU

220,33 € HT
264,39 € TTC

En stock
2 pièces

Ram Mounts RAM SKIN FOR SAMSUNG GALAXY TAB ACTIVE 5

(référence créée le 13.05.25) RUT7599 RAM-SKIN-SAM91

19,47 € HT
23,36 € TTC

Sur
Commande

Ram Mounts UNPKD RAM USB-C POWER ONLY KEYED LOCKING CRADLE FOR TAB

(référence créée le 16.04.25) RUT7598 RAM-HOL-SAM58CPKLNU

136,73 € HT
164,07 € TTC

Sur
Commande

Ram Mounts RAM® Powered Dock & Dashboard Mount for Samsung Tab Active4

(référence créée le 10.04.25) RUT7597 RAM-101-225B2-SAM52CP-V7CU

193,82 € HT
232,58 € TTC

Sur
Commande

Ram Mounts GDS® Shoulder Strap Accessory for IntelliSkin® Thin-CaseT

(référence créée le 10.04.25) RUT7596 RAM-GDS-SS1-TCU

17,49 € HT
20,98 € TTC

Sur
Commande

Ram Mounts RAM® Tough-MagT Heavy Duty Magnetic Mount with Round

(référence créée le 01.04.25) RUT7595 RAM-101-B-MAG88U

96,58 € HT
115,89 € TTC

Sur
Commande

Ram Mounts RAM® Tough-MagT Heavy Duty Magnetic Mount with Round

(référence créée le 01.04.25) RUT7594 RAM-101-MAG88U

98,45 € HT
118,14 € TTC

Sur
Commande

Ram Mounts UNPKD RAM 88MM DIA BASE WITH SHORT ARM

(référence créée le 24.03.25) RUT7593 RAM-138-B-MAG88U

94,27 € HT
113,12 € TTC

Sur
Commande

Ram Mounts GDS® Uni-ConnT Locking Vehicle Bundle for Samsung

(référence créée le 12.02.25) RUT7591 RAM-GDS-U1-SAM88-KIT1

333,96 € HT
400,75 € TTC

Sur
Commande

Ram Mounts Locking GDS® Tough-DockT for Samsung Tab Active4 Pro

(référence créée le 31.01.25) RUT7590 RAM-GDS-DOCKL-SAM54NCPU

192,61 € HT
231,13 € TTC

Sur
Commande

Ram Mounts UNPKD EZ-ROLL'R DOCK USB-C POWER & 1 RJ45 + 1 USB-A

(référence créée le 30.01.25) RUT7589 RAM-HOL-SAM60CP-RJ45AU

146,52 € HT
175,82 € TTC

Sur
Commande

Ram Mounts GDS magnetic Wrist Strap for Zebra ET4x 10 Inch Enterprise Tablet

IntelliSkin Case or OEM Protective Case, Stand Function

(référence créée le 24.01.25) RUT7588 RAM-GDS-HS1M-ZE21U

60,16 € HT
72,19 € TTC

Sur
Commande

Ram Mounts Holder for Tablets with GDS® Uni-ConnT Button

(référence créée le 13.01.25) RUT7587 RAM-HOL-U1U

12,98 € HT
15,57 € TTC

Sur
Commande

Ram Mounts IntelliSkin® Thin-CaseT for iPad 10th Gen

(référence créée le 13.12.24) RUT7586 RAM-GDS-SKIN-AP40-TCD

73,48 € HT
88,17 € TTC

Sur
Commande

Ram Mounts RAM® Right Locking Holder for Tablets with GDS® Uni-ConnT

(référence créée le 13.12.24) RUT7585 RAM-HOL-U1LRU

38,06 € HT
45,67 € TTC

Sur
Commande

Ram Mounts RAM® USB-C Powered Dock for Tab Active5 & 3 with Hardwire

(référence créée le 06.12.24) RUT7584 RAM-HOL-SAM60CP-V7CU

134,31 € HT
161,17 € TTC

Sur
Commande

Ram Mounts RAM® Powered Dock for Honeywell ScanPal EDA10A

(référence créée le 29.11.24) RUT7583 RAM-HOL-HON11PU

147,62 € HT
177,14 € TTC

Sur
Commande

Ram Mounts RAM® SkinT for Samsung Galaxy XCover7

(référence créée le 28.11.24) RUT7582 RAM-SKIN-SAM94

28,38 € HT
34,05 € TTC

Sur
Commande

Ram Mounts UNPKD NON-LOCKING LATCH DOCK POWER ONLY FOR ZEBRA ET40/45

(référence créée le 28.11.24) RUT7581 RAM-HOL-ZE20PNLLU

138,16 € HT
165,79 € TTC

Sur
Commande

Ram Mounts GDS VEHICLE DOCK HIGH SPEED USBC FOR SAMSUNG TAB ACTIVE

(référence créée le 28.11.24) RUT7580 RAM-GDS-DOCK-SAM54NCPU

158,07 € HT
189,68 € TTC

Sur
Commande

Ram Mounts RAM® EZ-Roll'rT Power + Data Dock Samsung Tab Active5 & 3

(référence créée le 18.11.24) RUT7579 RAM-HOL-SAM60CP-1AU

82,06 € HT
98,47 € TTC

Sur
Commande

Ram Mounts RAM® Low-Profile USB-C Powered Dock for Tab Active5

(référence créée le 18.11.24) RUT7578 RAM-HOL-SAM58CPTU

111,65 € HT
133,98 € TTC

Sur
Commande

Ram Mounts RAM GDS INTELLISKIN FOR IPAD PRO 11" M4 2024

(référence créée le 15.11.24) RUT7577 RAM-GDS-SKIN-AP46-NG

75,79 € HT
90,94 € TTC

Sur
Commande

Ram Mounts GDS® Hand Strap for Phones with IntelliSkin® or RAM®

(référence créée le 12.11.24) RUT7576 RAM-GDS-HS4U

16,72 € HT
20,06 € TTC

Sur
Commande

Ram Mounts RAM GDS INTELLISKIN FOR IPAD AIR 13" M2 2024 + IPAD PRO

(référence créée le 12.11.24) RUT7575 RAM-GDS-SKIN-AP47-NG

88,88 € HT
106,65 € TTC

Sur
Commande

Ram Mounts IntelliSkin® Next Gen for Samsung Tab Active5

(référence créée le 06.11.24) RUT7574 RAM-GDS-SKIN-SAM90-NG

75,57 € HT
90,68 € TTC

Sur
Commande


Société (facultatif) :
Nom :
Prénom :
Fonction (Facultatif) :
Téléphone :
E-mail :
Message :


	Demande enregistrée

	Nous vous confirmons le bon enregistrement de votre demande. Un mail de confirmation vous a été envoyé.

	Fermer

Quantité ajoutée :

Votre e-mail :